[PW_SID:962869] Add Sophgo EVB V1/V2 Board support

Documentation/devicetree/bindings/riscv/sophgo.yaml

@@ -34,6 +34,8 @@ properties:
       - items:
           - enum:
               - milkv,pioneer
+              - sophgo,sg2042-evb-v1
+              - sophgo,sg2042-evb-v2
           - const: sophgo,sg2042
 
 additionalProperties: true

arch/riscv/boot/dts/sophgo/Makefile

@@ -3,3 +3,5 @@ dtb-$(CONFIG_ARCH_SOPHGO) += cv1800b-milkv-duo.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += cv1812h-huashan-pi.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2002-licheerv-nano-b.dtb
 dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-milkv-pioneer.dtb
+dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v1.dtb
+dtb-$(CONFIG_ARCH_SOPHGO) += sg2042-evb-v2.dtb

arch/riscv/boot/dts/sophgo/sg2042-evb-v1.dts

@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 Sophgo Technology Inc. All rights reserved.
+ */
+
+#include "sg2042.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Sophgo SG2042 EVB V1.X";
+	compatible = "sophgo,sg2042-evb-v1", "sophgo,sg2042";
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	gpio-power {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power Key";
+			linux,code = <KEY_POWER>;
+			gpios = <&port0a 22 GPIO_ACTIVE_HIGH>;
+			linux,input-type = <EV_KEY>;
+			debounce-interval = <100>;
+		};
+	};
+};
+
+&cgi_main {
+	clock-frequency = <25000000>;
+};
+
+&cgi_dpll0 {
+	clock-frequency = <25000000>;
+};
+
+&cgi_dpll1 {
+	clock-frequency = <25000000>;
+};
+
+&emmc {
+	pinctrl-0 = <&emmc_cfg>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	no-sdio;
+	no-sd;
+	non-removable;
+	wp-inverted;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mcu: syscon@17 {
+		compatible = "sophgo,sg2042-hwmon-mcu";
+		reg = <0x17>;
+		#thermal-sensor-cells = <1>;
+	};
+};
+
+&gmac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		phy0: phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&port0a 27 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <100000>;
+			reset-deassert-us = <100000>;
+		};
+	};
+};
+
+&pinctrl {
+	emmc_cfg: sdhci-emmc-cfg {
+		sdhci-emmc-wp-pins {
+			pinmux = <PINMUX(PIN_EMMC_WP, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+
+		sdhci-emmc-cd-pins {
+			pinmux = <PINMUX(PIN_EMMC_CD, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+
+		sdhci-emmc-rst-pwr-pins {
+			pinmux = <PINMUX(PIN_EMMC_RST, 0)>,
+				 <PINMUX(PIN_EMMC_PWR_EN, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+	};
+
+	i2c1_cfg: i2c1-cfg {
+		i2c1-pins {
+			pinmux = <PINMUX(PIN_IIC1_SDA, 0)>,
+				 <PINMUX(PIN_IIC1_SCL, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+	};
+
+	sd_cfg: sdhci-sd-cfg {
+		sdhci-sd-cd-wp-pins {
+			pinmux = <PINMUX(PIN_SDIO_CD, 0)>,
+				 <PINMUX(PIN_SDIO_WP, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+
+		sdhci-sd-rst-pwr-pins {
+			pinmux = <PINMUX(PIN_SDIO_RST, 0)>,
+				 <PINMUX(PIN_SDIO_PWR_EN, 0)>;
+			bias-disable;
+			drive-strength-microamp = <26800>;
+			input-schmitt-disable;
+		};
+	};
+
+	uart0_cfg: uart0-cfg {
+		uart0-rx-pins {
+			pinmux = <PINMUX(PIN_UART0_TX, 0)>,
+				 <PINMUX(PIN_UART0_RX, 0)>;
+			bias-pull-up;
+			drive-strength-microamp = <26800>;
+			input-schmitt-enable;
+		};
+	};
+};
+
+&sd {
+	pinctrl-0 = <&sd_cfg>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	wp-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/ {
+	pwmfan: pwm-fan {
+		compatible = "pwm-fan";
+		cooling-levels = <103 128 179 230 255>;
+		pwms = <&pwm 0 40000 0>;
+		#cooling-cells = <2>;
+	};
+
+	thermal-zones {
+		soc-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+			thermal-sensors = <&mcu 0>;
+
+			trips {
+				soc_active1: soc-active1 {
+					temperature = <30000>;
+					hysteresis = <8000>;
+					type = "active";
+				};
+
+				soc_active2: soc-active2 {
+					temperature = <58000>;
+					hysteresis = <12000>;
+					type = "active";
+				};
+
+				soc_active3: soc-active3 {
+					temperature = <70000>;
+					hysteresis = <10000>;
+					type = "active";
+				};
+
+				soc_hot: soc-hot {
+					temperature = <80000>;
+					hysteresis = <5000>;
+					type = "hot";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&soc_active1>;
+					cooling-device = <&pwmfan 0 1>;
+				};
+
+				map1 {
+					trip = <&soc_active2>;
+					cooling-device = <&pwmfan 1 2>;
+				};
+
+				map2 {
+					trip = <&soc_active3>;
+					cooling-device = <&pwmfan 2 3>;
+				};
+
+				map3 {
+					trip = <&soc_hot>;
+					cooling-device = <&pwmfan 3 4>;
+				};
+			};
+		};
+
+		board-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+			thermal-sensors = <&mcu 1>;
+
+			trips {
+				board_active: board-active {
+					temperature = <75000>;
+					hysteresis = <8000>;
+					type = "active";
+				};
+			};
+
+			cooling-maps {
+				map4 {
+					trip = <&board_active>;
+					cooling-device = <&pwmfan 3 4>;
+				};
+			};
+		};
+	};
+};