New Crowdin updates

docs/CROWDIN/cs/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/de/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Der Freestyle Libre 3 (FSL3) benötigt ein besonderes Setup, um Glukosewerte in
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**AAPS Version 3.2.0.1 unterstützt keine minütlichen Werte. Beschleunigung und Glättung funktionieren nicht mit minütlichen Werten.**
-
 Um das zu beheben, wird in den unten beschriebenen Methoden Juggluco als separate App eingesetzt. Juggluco reicht die minütlichen unveränderten Daten (Rohdaten) des Sensors an xDrip+ oder AAPS weiter. Neu gesetzte Sensoren können entweder mit der Libre 3 App oder direkt in Juggluco gestartet werden. Die Anleitung unten beschreibt, wie ein Sensor mit der Juggluco-App gestartet werden kann. Wenn der Sensor mit einem eingeloggten Libreview-Konto gestartet wurde, ist es auch möglich, zwischen Juggluco und der Libre 3 App als Empfänger zu wechseln.
 
 Wenn der Sensor mit der Libre 3 App gestartet wird, können Deine Daten über Juggluco und LibreView z. B. mit Deinem Diabetes-Team geteilt werden.
 
 Der Sensor kann in xDrip+ im Bereich von -40 mg/dl bis +20 mg/dl (-2.2 mmol/l bis +1.1 mmol/l) kalibriert werden. Damit kannst Du die Differenz zwischen einer blutigen Messung und den Sensorwerten anpassen.
 
 ## Methode 1: Minütliche Werte
-AAPS Version 3.2.0.1 unterstützt keine minütlichen Werte. Beschleunigung und Glättung funktionieren nicht mit minütlichen Werten.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/el/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/es/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ El Freestyle Libre 3 (FSL3) requiere una configuración especial para recibir lo
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**La versión 3.2.0.1 de AndroidAPS no soporta valores de 1 minuto. Acceleration and Smoothing does not work with 1-minute values.**
-
 Los siguientes métodos para lograr esto utilizan la aplicación independiente Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. Los nuevos sensores se pueden iniciar tanto con la aplicación Libre 3 como directamente en Juggluco. La guía a continuación indica el proceso para iniciar un sensor con la aplicación Juggluco. Si el sensor se ha iniciado con una cuenta de Libreview conectada, también es posible alternar entre Juggluco y la aplicación de Libre 3 como receptor.
 
 Juggluco también puede enviar datos a LibreView para compartirlos con los equipos médicos, cuando el sensor se inicia con la aplicación Libre 3.
 
 Dentro de xDrip+, el sensor se puede calibrar en un rango de -40 mg/dl a +20 mg/dl (-2,2 mmol/l a +1,1 mmol/l) para compensar las diferencias entre una lectura manual de medidor y las lecturas del sensor.
 
 ## Method 1: 1-minute-readings
-La versión 3.2.0.1 de AndroidAPS no soporta valores de 1 minuto. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/fr/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/he/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/ko/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/lt/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/nl/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/pb/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/pl/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/pt/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)
 

docs/CROWDIN/ro/CompatibleCgms/Libre3.md

@@ -8,16 +8,14 @@ Freestyle Libre 3 (FSL3) requires a unique setup to receive BG values in to AAPS
 
 ![FL3](../images/d912c1d3-06d2-4b58-ad7c-025ca1980fae.jpeg)
 
-**Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.**
-
 The below methods for achieving this are using the separate app Juggluco. It uses Juggluco to receive raw, 1-minute interval data from the sensor which is then passed to xDrip+ or AAPS. New sensors can be started either with the Libre 3 App or directly in Juggluco. The guide below indicates the process for starting a sensor with the Juggluco app. If the sensor has been started with a Libreview account logged in, it is also possible to switch between Juggluco and the Libre 3 app as receiver.
 
 Juggluco can also pass data to LibreView for sharing with health care providers when the sensor is started with the Libre 3 app.
 
 Within xDrip+ the sensor can be calibrated in the range of -40 mg/dl to +20 mg/dl (-2.2 mmol/l to +1.1 mmol/l) to compensate for differences between a manual meter reading and the sensor readings.
 
 ## Method 1: 1-minute-readings
-Version 3.2.0.1 of AndroidAPS does not support 1-minute values. Acceleration and Smoothing does not work with 1-minute values.
+AndroidAPS does not process 1-minute values.
 
 ![Juggluco broadcast to AAPS](../images/Juggluco_AAPS.png)